Quantcast
Channel: Popular Science | RSS
Viewing all 20161 articles
Browse latest View live

China Tests its Largest Airship

$
0
0
China Yuanmeng airship

Yuanmeng

cannews.com

This concept art shows China's 18,000 cubic meter Yuanmeng airship 20km above the ground (and for some reason, off the coast of the Mid Atlantic U.S.). One of the highest flying airships, the Yuanmeng can provide wide area surveillance and communications capability.

On October 13, 2015, China started the 24 hour test flight of its largest airship yet in Xilinhot, Inner Mongolia. The Yuanmeng has a volume of 18,000 cubic meters, length of 75 meters and 22 meters height. It will fly to 20,000 meters to test its control systems and near space flight performance. With solar panels installed on its top, the Yuanmeng will be one of the largest solar powered airships in existence, using solar power to drive its rotors will save additional weight in order to increase payload. Solar power also gives it a total flight endurance of six months. The Yuanmeng's 5-7 ton payload of data relays, datalinks, cameras and other sensors would also be powered by the sun.


China Yuanmeng airship

High Concept

=GT at China Defense Forum

This poster from Yuanmeng's manufacturer brags about its capability to fly at over 20km altitude, as well as sensor and communications capabilities. This airship is almost entirely powered by solar panels on its topside.

Like its smaller American counterpart, the JLENS (currently parked outside Washington DC), the Yuanmeng can use its sensors and high altitude to detect threats such as stealth aircraft, cruise missiles, missile launchers and warships from several hundred miles away. But the Yuanmeng also advantages over the JLENS. While the JLENS is an aerostat, anchored to one location by a 3,000m long tether, the Yuanmeng can freely move about and be redeployed. Its high flight altitude also gives the Yuanmeng's sensors superior situational awareness, and the ability to act as a communications rely to Chinese aircraft and drones in the event of a loss in satellite communications.


China Yuanmeng airship

By the Power of the Sun

NNTV

Solar panels lie on the hangar floor, ready to be attached to the Yuanmeng once it's fully inflated.

Yu Quan, a scientist of the Chinese Academy of Engineering, notes that airships are ideal for long duration flights in near space (the atmosphere between 20km to 100km altitude) though thermal expansion from day and night temperature differentials are a design issue. Operating higher in near space means that the Yuanmeng would have constant line of sight over a hundred thousand square miles, an important requirement for radar and imaging. Increased sensor coverage means increased warning time against stealthy threats such as cruise missiles, giving Chinese forces a greater opportunity to detect and shoot down such threats. It would also be harder for fighters and surface to air missiles to attack near space objects.

China airship

Chinese Airship

huanqiu.com

This airship, apparently a Golden Eagle, is a predecessor to the Yuanweng. China has conducted low level research into airships since the 1960s.

The program may be the start of a wider portfolio of large airships. China Aviation Industry General Aircraft Co. Ltd. (CAIGA), a subsidiary of China Aviation Industry Group, has partnered with Flying Whales, a French company to build heavy airships, with a 60 ton payload cargo airship reported to be their first aircraft.

You may also be interested in:

What will the next Chinese Spaceship Look Like?

Chinese Hypersonic Engine Wins Award, Reshapes Speed Race?

A Closer Look at China's Divine Eagle Drone

Divine Eagle, China's Stealth Hunting Drone, Takes Shape

China Flies Its Largest Drone Ever: the Divine Eagle

The New Inflatable Chinese Drone: Battlefield Balloons?

China Shows Off Growing Drone Fleet


Real-Time Video Software Puts Someone Else's Facial Expressions On Your Face

$
0
0

Demonstrating the live facial reenactment technique

Researchers from the University of Erlangen-Nuremberg, the Max Planck Institute for Informatics, and Stanford University have developed a new method for "real-time facial reenactment." This means that you can have one person making faces or mouthing words, and those expressions and movements are simultaneously displayed on live video of the face of someone else.

Previously, we've seen video technology that could (sort of) graft a celebrity's face onto your own in real time, but this system, moving your own facial features around under someone else's guidance, is arguably creepier

"Facial reenactment," as the paper notes, is a bit more difficult than just mapping expressions onto a computer-generated avatar, which is known as re-targeting. "Reenactment is a far more challenging task than expression re-targeting, as even the slightest errors in transferred expressions and appearance and slight inconsistencies with the surrounding video will be noticed by a human user," the study authors write.

They solved most of the problems by tracking the geometry, reflectance, and texture of the faces for both the source actor (who's making the expressions) and the target actor. To deal with pesky details like teeth, they simulate what the interior of a mouth would look like, complete with teeth proxies. The results are composited to create a pretty realistic video. The technology does still have minor shortcomings. For example, waving a hand in front of the face could lead to freaky distortions, and glasses also pose a slight disruption in the image.

You can only begin to think of the possibilities: You never have to smile again, as long as there's someone else smiling for you; you can put a beard on your face without having to grow it; and of course they could do something useful like make your mouth movements match dubbed dialogue. Watch the video below for a full explanation of how the technology works.

[via Joshua Topolsky]

Video: A Master Swordsman Cuts A 100-MPH Fastball In Half

$
0
0

The last time we checked in with Isao Machii, the Japanese master of Iaido (which is a modern martial art involving swordplay), he was demonstrating his expertise of Iaijutsu, or quick draw, with an MH24 robot arm. The pair sliced through flowers, fruit, and peapods, and littered the floor with thousands of mangled practice targets.

Perhaps Machii's real skill, though, is using his reflexes and superb hand-eye coordination to cut speeding objects in half. To wit: Machii has halved a fried shrimp (80 mph), a BB bullet (200 mph), a tennis ball (400-plus mph), and now a baseball at roughly 100 mph.

[via Kotaku]

New Kittens For Koko, An Indoor Coral Reef, And Other Amazing Images Of The Week

3-D Printed Artificial Teeth Could Stop Bacteria

$
0
0
Bacteria In Petri Dishes

Bacteria In Petri Dishes

Jun Yue et al

Red dots are dead bacteria, green dots are live bacteria. On the left are samples without the special salt, on the right are samples with the bacteria-killing salt.

Lost a tooth? A new 3D-printed replacement might protect against future cavities. Published earlier this month by researchers at the University of Groningen in the Netherlands, “3D-Printable Antimicrobial Composite Resins” details a tooth made from materials that kill bacteria on contact. The researchers set out to create a tooth that bacteria wouldn’t destroy, and created a dental guardian.

Here’s how it works. The replacement tooth is designed to match the gap in the person’s mouth. A resin, made of safe materials combined with a special salt, is then printed into the shape of the tooth and then placed like a normal replacement into the person’s mouth. The positive charge in the salts in the resin bursts negatively-charged bacterial membranes, leaving only dead colonies where once were festering feeding frenzies of microbial intruders.

To test the work, they printed objects both with and without the microbial salts, and then put tooth decay-causing Streptococcus mutans on the samples. Without the salts, only about 1 percent of the bacteria on the items died. With the incorporated salts, over 99 percent of colonies vanished.

The authors of the paper are enthusiastic about its success and future uses, writing:

The antimicrobial properties were shown to be caused by bacterial contact killing with the material rather than the release of antimicrobial compounds from the resin. Having optimized the activity and stability of these materials, we have a prototype at hand that is suited for further testing in a clinical setting, including not only dental applications but also, for instance, orthopedic ones like spacers and other polymeric parts used in total hip or knee arthroplasties. Moreover, the approach to developing 3D printable antimicrobial polymers can easily be transferred to other nonmedical application areas, such as food packaging, water purification, or even toys for children. To the best of our knowledge, the resins we developed represent the first report of an antimicrobial, contact-killing 3D printable material.

[New Scientist]

Could Having Your DNA Tested Land You In Court?

$
0
0

The story of filmmaker Michael Usry’s arrest seems like it could have come straight from an episode of CSI. A New Orleans-based filmmaker known for his violent, murder-centered films, he was suspected of the 1996 murder of a young woman in Idaho Falls, Idaho. In early 2015, using DNA his father submitted to a private genetics company owned by Ancestry.com, police narrowed down on the filmmaker. Usry submitted his DNA to authorities and when it didn't match, he was found innocent. However, as Wired reports in an article today, the method the cops used to narrow down on Usry--employing private genetics companies' databases to find a suspect--brings to the forefront the already heightened concerns over the use and privacy laws of commercial DNA testing through companies such as Ancestry and 23andMe.

Back in 1996, a suspect was convicted of the murder soon after it took place. However, amid concerns that the wrong man was convicted, the police turned to a controversial technique known as familial searching, which searches a DNA database to look for close biological relatives to unknown DNA that was obtained at the crime scene. The technique looks for partial matches where both DNA share common alleles, or pieces of DNA.

Using this method, the Idaho Falls authorities matched Usry’s father with 34 of the 35 alleles. His father had entered his DNA samples into the Sorenson Molecular Genealogy Foundation, which had been acquired through Ancestry. They searched for his close relatives and narrowed down on Usry, claiming he had ties to the area where the crime was committed, and that his murder-based horror films were signs of his deranged mind.

When they tested Usry’s DNA, though, it didn’t match the DNA that was found at the crime scene. In an interview with The New Orleans Advocate, where Usry’s story was first reported, Sgt. James Hoffman of the Idaho Falls Police Department said, “It turned out to be nothing. I wish it wasn’t a dead end, but it was.”

However, his story most certainly opens the doors for concern over whether familial searching should be used, and, perhaps just as importantly, whether police who are looking to make an arrest should be allowed access to the DNA found in private databases like Ancestry and 23andMe, to which individuals who are curious about their health or family lineage submit their DNA.

Back when Ancestry and 23andMe first started sending out DNA kits, skeptics raisedconcerns over what the companies were going to do once they had a ginormous database of human DNA. Concerns over whether they were going to sell the DNA to drug companies or insurance companies are still being raised and now, given Usry’s case, law enforcement and crime stopping can be added to the list.

As Fusion reports, the FBI already has a national genetic database, but this instance is the first time they employed private genetic databases to narrow down their search. Both companies’ policies mention that, if given a court order, they will turn DNA information over to authorities, and they acknowledge that this has happened before, and they have complied.

23andMe’s privacy officer, Kate Black (who just joined the company in February) tells Fusion that the company plans to publish a transparency report in the next few months, which would detail the exact amount of government requests that it receives and how many it actually complies with. “In the event we are required by law to make a disclosure, we will notify the affected customer through the contact information provided to us, unless doing so would violate the law or a court order,” Black tells Fusion.

Ancestry hasn’t mentioned any plans to provide a similar report just yet. The database that was used to find Usry was already available to the public. Since then, the database has been taken down. Further, when the police came to Ancestry.com with a warrant to get Usry’s father’s name, the company complied.

Usry’s case is not likely to be the last like it. As the cost of DNA analysis gets cheaper and the amount of DNA companies have continues to grow, the use of familial DNA searching is only going to increase, reports Wired. Perhaps Usry’s case is a cautionary tale for all parties involved. In the future, states may consider whether public safety authorities should be able to run searches through private genetic databases. And, as Fusion reports, “If the idea of investigators poking through your DNA freaks you out, both Ancestry and 23andMe have options to delete your information with the sites. 23andMe says it will delete information within 30 days upon request.”

Lockheed Mounted A Laser Turret On Business Jet

$
0
0
Air Force Research Laboratory

Lockheed Martin Turret On Airplanea

Air Force Research Laboratory

Lasers could be the future of aerial warfare. Defense giant Lockheed Martin, which has already tested a directed energy weapon (or laser) on the ground, announced yesterday 60 successful tests of a laser turret on a business jet between 2014 and 2015. While the turret only fired a low-powered laser, it’s still a success because it was able to counteract the effect of turbulence on the beam. From the release:

The design uses the latest aerodynamic and flow-control technology to minimize the impacts of turbulence on a laser beam. An optical compensation system, which uses deformable mirrors, then is used to ensure that the beam can get through the atmosphere to the target. Left unchecked, turbulence would scatter the light particles that make up a laser beam, much like fog diffuses a flashlight beam.

If the test carries over to more high-powered lasers, then airplanes will be able to use the same kinds of energy weapons as those on ships and on the ground.

Last year, in conversation with Popular Science, Lockheed’s Chief Technology Officer said of an airborne laser weapon: “It’s game changing. Should you develop an operational weapon that operates at Mach a million, that’s game changing.” This turret is part of that package. The program, funded by DARPA and the Air Force Research Laboratory, is called “Aero-adaptive Aero-optic Beam Control”, and it’s been in the works for some time. One promise of the technology: defending larger airplanes, much like machine gun turrets protected bombers in World War II. Only this time, instead of shooting down fighter jets, the lasers could also stop missiles and drones.

The U.S. Interior Department Halts Future Arctic Oil Drilling

$
0
0

A platform designed for arctic oil exploration

Royal Dutch Shell

The Interior Department announced today it will stop selling new Arctic drilling leases for future scheduled sales, and it will not extend leases currently held by companies like Royal Dutch Shell.

This comes not long after Shell's own announcement in late September, that it would stop its controversial oil exploration in Alaska just five months after it started, because it found little oil.

“In light of Shell’s announcement, the amount of acreage already under lease and current market conditions, it does not make sense to prepare for lease sales in the Arctic in the next year and a half,” Secretary of the Interior Sally Jewell said a press release.

The news is likely to be welcomed by environmental advocates who opposed Arctic drilling over concerns about increased carbon emissions and the potential for accidental spills, which would be more difficult to clean up in the extreme environment

Shell's lease is set to expire in 2020, and Statoil's lease is up in 2017.


Nintendo NX May Be A Portable/Home Console Hybrid

$
0
0

Nintendo NX Rumors

Xavier Harding

Much like controlling Super Smash Bros 4 on the Wii U with the 3DS, Nintendo's next generation hardware could see a home console working alongside a handheld

Nintendo has kept a tight lid regarding Project NX--the company's next-generation console. After revealing initial details about the new console back in March, Iwata confirmed we wouldn't see anything come until 2016. Or so we thought.

The Wall Street Journal reports that game makers have already started receiving development kits. Even more interesting is that developers familiar with kit have noted the likeliness of “one mobile unit that could either be used in conjunction with the console or taken on the road for separate use,” claims WSJ.

The use of the word “mobile” could hint at Nintendo’s increasing embrace of the smartphone scene with the help of DeNA. Though, more likely, the Japanese gaming company is making the Nintendo NX a combined home console and handheld device.

Wii U titles like Super Smash Bros 4, which can utilize Nintendo’s 3DS portable system as a controller, show that providing dual uses in this way is entirely possible. Many, including Mario and Zelda's creator, Shigeru Miyamoto, consider Nintendo's Wii U a failure. But the company sees much greater success in its portable offerings--often dominating the on-the-go arena. If the gaming giant can bring some of their handheld console magic to the full console attached to your TV, it could prove to be good for gamers and Nintendo.

The Nintendo NX release date is rumored to hit in 2016.

Apple’s Newest ResearchKit Apps Will Study Autism, Epilepsy, And Melanoma

$
0
0

ResearchKit

Apple announced yesterday that it is planning to use its ResearchKit platform to study three huge health problems: epilepsy, autism, and melanoma.

ResearchKit--Apple's open-source health software platform that lets researchers design apps for medical research--was launched seven months ago and has already been used by researchers across the country to study diseases like Parkinson's and asthma.

Now research institutions are launching three new apps,. Combined with the tools already available on ResearchKit, the company hopes the apps will allow more people to participate in clinical trials, which will provide researchers with more data from a diverse background--a crucial component for studying how and why certain diseases occur.

With ResearchKit, researchers can study participants from around the world, not just near where the study is based. And with the help of the open source platform, researchers can incorporate the iPhone’s camera, accelerometer, microphone, gyroscope, and GPS sensors into their studies. Here are the three latest apps and how they will work:

10 Brain Myths Busted

$
0
0

In the Hollywood action-film Lucy, actor Morgan Freeman—playing a world-renowned neurologist— speaks to a packed auditorium. “It’s estimated most human beings only use 10 percent of their brains’ capacity,” he says. “Imagine if we could access 100 percent.” You may have heard that claim before. Unfortunately, it’s just not true. And after watching Lucy, Ramina Adam and Jason Chan, two neuroscience graduate students at Western University in Ontario, decided to set the record straight. “We realized we had to do something about all this misinformation,” Adam says. They set out to collect common mis­perceptions about how the brain works, and we lent a hand in debunking them.

Click through the gallery above to find out the truth about 10 common neuroscience myths.

How To Stay Sharp

While crossword puzzles and classical music aren’t going to make you smarter, here are three proven strategies to keep your brain at peak performance for your entire life.

1. Get The Blood Flowing

In a 2014 study at the University of British Columbia in Canada, women who walked briskly for an hour twice weekly for six months—but not those who strength-trained or did no exercise—increased brain volume in the areas that control thinking and memory.

2. Eat Your Greens

A team of researchers with the federally funded Nurses’ Health Study tracked 13,388 women over decades and discovered the more leafy vegetables they ate, the better they performed on learning and memory tests. That might be due in part to folic acid in veggies: A long-term study of 60 Roman Catholic nuns in Minnesota identified folic acid as a key factor in delaying the onset of dementia.

3. Talk To People

In 2004, scientists at Johns Hopkins University found that more social interaction was associated with less cognitive decline for people aged 50 and above. Plus, one of the major risk factors for death in the elderly is social isolation—lone­liness really can kill you.


Plot Twists

“Neuromyths have gotten folded into popular culture,” says Nicholas Spitzer, co-director of the Kavli Institute for Brain and Mind at the University of California at San Diego. “It’s been an uphill battle to dispel them.” Here are three culprits from TV and the movies.—Nicole Lou

Myth #1. Alcohol kills brain cells

Courtesy Fox

Before taking his remedial high school science exam, Homer says in The Simpsons (1993), “All right, brain. You don’t like me and I don’t like you, but let’s just do this and I can get back to killing you with beer.”

Myth #2. ESP is a scientific certainty

Everett Collection

The premise of Steven Spielberg’s Minority Report (2002) rests on the ability of a psychic police force to stop murders before they happen (and gives rise to a slew of ESP-centric crime shows, such as Medium).

Myth #3. Being in a coma is like being asleep

Everett Collection

A single mosquito bite awakens Beatrix Kiddo, the Bride in Quentin Tarantino’s Kill Bill: Vol. 1 (2003). After spending four years in a coma, she is able to get out of bed and immediately begin a killing spree.

This article was originally published in the November 2015 issue of Popular Science, under the title “Brain Myths Busted.”

General Relativity: 100 Years Old And Still Full Of Surprises

$
0
0

Albert Einstein

Library of Congress—Oren Jack Turner/Getty Images

In 1947, at age 67, Einstein persevered in developing a single unified theory that would combine electromagnetism and gravity — a quest that still eludes physicists today.

In 1913, Albert Einstein had stalled in his efforts to construct his general theory of relativity. He pleaded with his friend Marcel Grossmann for a mathematical boost: “Grossmann, you’ve got to help me, otherwise I’ll go mad!” Four years later, as Einstein was finishing a paper on the cosmic implications of his (finally) completed theory, the malady had migrated to other parts of the body. He had a stomach ulcer; he suffered from liver disease. Worn out by his mental exertions, Einstein thought he was dying. He wrote to fellow physicist Arnold Sommerfeld: “In the last month I had one of the most stimulating, exhausting times of my life, indeed also one of the most successful.”

That sensation eluded most of his colleagues back then, and it still does. They study Einstein’s greatest insight without fully grasping how he achieved it, or what it meant to him; they typically don’t “feel relativity in their bones,” in the words of Columbia University theoretical physicist Brian Greene. The lack of understanding comes from a sticky misconception of what general relativity is, even among those who spend their careers making use of it. It is broadly described as a theory of gravity, but it is not just a theory. It is written out as a series of equations describing how objects move, but it is not just equations.

General relativity is best thought of as a landscape, both literally and figuratively. It is an expanse of concepts that describes all the possible configurations of space and time, and all the ways they change in the presence of matter. It is a system in which every part of reality is connected. Einstein’s first forays into that landscape were what so exhilarated and drained him. Whenever other researchers manage to follow his lead, they discover whole new regions. That is why, a century after it was first published, general relativity is yielding its most astonishing discoveries yet.

II.

There is no better way to take in the idea of relativity-as-­landscape than by looking at the biggest landscape of all: the universe. Einstein realized that space is not a fixed background (a kind of invisible ruler that you can measure motion against), but rather a flexible, dynamic thing that bends and distorts in response to mass. That bending is what we experience as a gravitational pull: It holds your feet to the ground and Earth in its orbit. Lee Smolin—a theorist at the Perimeter Institute for Theoretical Physics in Waterloo, Ontario, and one of Einstein’s most vocal disciples—praises general relativity’s ability to provide a single, unified description of all space, as determined by all mass. “It’s the first theory that can be applied to the universe as a whole in a closed system,” he says.

“It’s the first theory that can be applied to the universe as a whole in a closed system.”

You’ve surely heard scientists say that the universe is expanding, but what does that really mean? In 1929, Edwin Hubble observed that galaxies appear to be moving away from ours in all directions. It is tempting to picture those galaxies flying through space, driven apart by a tremendous initial explosion. In fact, in the 1930s, British astronomer E.A. Milne attempted to describe Hubble’s discovery in just those terms. His analysis was a dismal failure. The only way to make sense of the astronomical observations, Einstein showed, is to think of space as a dynamic thing. Galaxies are not flying through space; space itself is expanding between them.

That is a profoundly weird notion, but once you make peace with it, all kinds of other ideas fall into place. First and foremost, there is the Big Bang, which was not an explosion in space but an explosion of space. All of space was crammed into a single dot at the moment of the Big Bang, and all of space expanded out from there in the 13.7 billion years since. Because space is expanding in all directions, any spot can be considered the center of the universe. You, right there, right now, are at the center of the universe. (How’s that for an ego boost?) Relativity is what allowed cosmologists to model the origin of the elements, the formation of galaxies, the direct evolutionary path from the Big Bang to modern Earth.

And still they are exploring new corners of relativity’s landscape. Because space is dynamic, it can deform in all kinds of complicated ways. The pull of gravity works to compress it; that compression is what you experience as your weight. Einstein’s equations also allow for antigravity, an energy that pushes space apart. For decades, that possibility was regarded as little more than a theoretical curiosity. Then in 1998, two teams of astronomers observed that the expansion of the universe is accelerating. This makes sense only in the context of relativity. The antigravity element driving the acceleration is now called “dark energy,” and it is so well-­accepted that the 2011 Nobel Prize in physics was awarded for its discovery.

The true nature of dark energy, however, remains an enigma. To figure it out, an international team of astronomers launched the Dark Energy Survey, currently underway at the Cerro Tololo Inter-American Observatory in Chile. Over the course of five years, they will be photographing 300 million galaxies and recording their distribution. Gravity tends to make galaxies clump together over time, whereas dark energy tends to scatter them. The pattern captured by the survey will begin to reveal whether dark energy works the same in all locations and whether its intensity has changed over the course of cosmic history. Dark energy outweighs all the visible galaxies by about 15-to-1, and so its influence might determine the fate of the universe.

You, right there, right now, are at the center of the universe. How’s that for an ego boost?

Just as space can expand, so it can ripple when disturbed by the gravity of a moving object, like the surface of a pond stirred by a skipping stone. This is another wilderness of relativity that scientists are only now exploring. As gravitational waves wiggle past Earth at the speed of light, they subtly squish and stretch everything they encounter—including you. The effect is exceedingly subtle. To discern these waves, researchers are upgrading a pair of 2.5-mile-long detectors—one in Washington state, one in Louisiana—called the Laser Interferometer Gravitational-Wave Observatory (LIGO), along with a complementary experiment called Virgo, located in Italy. By the end of the decade, they hope to observe gravitational signals emanating from spectacular but otherwise invisible cosmic events such as colliding black holes.

Ah, yes, black holes—perhaps the most famous of all the bizarre features that have emerged from the landscape of Einstein’s equations. Black holes are places where space curves in on itself; nowhere is relativity’s topography more tortured and intriguing. At the event horizon—the boundary of the hole—time comes to a halt and the atom-scale phenomena described by quantum mechanics are stretched out to the size of cities…or so it seems. General relativity also states that all parts of the universe should be continuous, meaning there should be no physical interruption between the inside and outside of a black hole. That apparent contradiction is inspiring a storm of new theories that go beyond scientists’ current understanding of the laws of physics.

Even in the twisted case of black holes, concepts that seem to reside in the impossibly remote fringes of the relativity landscape might be approachable to hard observation. A globe-spanning instrument called the Event Horizon Telescope, which consists of nine radio observatories scattered around the world, is gathering information right now to create the first direct images of the supermassive black hole at our galaxy’s center. The black hole itself won’t look like anything (it’s, um, black), but measurements of its size and surrounding structure could reveal the ways that mass distorts the structure of space. Any deviation from Einsteinian expectations would point the way to totally new physics concepts. The first meaningful images from the Event Horizon Telescope could come soon, perhaps within a decade.

III.

All of these ideas about the expanding universe, gravitational waves, and black holes took an excruciatingly long time to develop because they were hidden deep within the relativity landscape. Einstein himself was slow to accept the first two and never made peace with black holes, sniffing that the arguments for their existence were “not convincing,” and assuming that natural processes prohibited them from forming. Many writers, including famed physicist George Gamow, have presented Einstein’s resistance to these ideas as “blunders”—places where his great mind went off track. In reality, Einstein had opened up a landscape so vast that even he needed much more than a single lifetime to explore it.

Even as modern physicists press on far beyond where Einstein managed to go, their common assumption is that general relativity is not the final word. Relativity clashes with quantum mechanics—the set of rules describing the atomic-scale world—in its description of gravity and extreme objects like black holes. Forced to choose, most of today’s theorists pick quantum mechanics as the more fundamental description of reality, regarding relativity as a large-scale phenomenon built from small-scale quantum effects. Physicists have done very well working from the bottom up (think of light interpreted as collections of photons, or matter as clusters of atoms), yet a century of experience suggests it is unwise to underestimate the power of Einstein’s top-down perspective. As Lee Smolin puts it, quantum mechanics is a theory of “subsystems”—that is, it makes sense only in the context of its surroundings—in contrast to relativity’s inherently cosmic scope.

Einstein’s holistic approach is what makes general relativity unique in its potential for explanation and exploration. Surely there will be future physicists who venture even further into reality than he did. They may very well adopt many of the tools and techniques of quantum theory. But just as surely, those geniuses will have to act like Einstein—stepping back from equations to see the larger landscape—if they want to attain true enlightenment. They will have to feel relativity in their bones.

Einstein's Work And Life

Images from top to bottom: Corbis; Corbis; Bettmann/Corbis; Hulton-Deutsch Collection/Corbis

Albert Einstein formulated general relativity (GR) over the course of a decade, and then ruminated on its implications for the rest of his life. Though GR kept him busy, the physicist found time to ponder a host of other ideas—and do a lot of living. The Einstein Papers Project, based at Caltech, shows as much. The team is curating, digitizing, and translating Einstein’s notebooks and letters to help scholars understand what occupied his mind. The 14 volumes published so far—through 1925, when Einstein was 46—reveal a hardworking scientist who wasn’t afraid to unleash some sass. —Shannon Palus

This article originally appeared in the November 2015 issue of Popular Science under the title "Albert Einstein, Landscape Architect."

Fold A Paper Robot With An Arduino Brain

$
0
0

Origami Robot

Photograph by Bryan Edwards

Liz Kruesi based this robot on Ankur Mehta's (MIT CSAIL) design, although she made a few minor changes. The daughter board was designed by Benjamin Shaya (MIT).

Origami, the ancient art of paper folding, also shows up in modern science and engineering. By turning a two-dimensional sheet into a 3-D product, as origami artists do, engineers can make more-versatile versions of devices like space mirrors and heart stents. The same techniques can also be used to create inexpensive robots.

To get started, simply print out a template, cut, and fold. Once you add some basic electronics, an Arduino brain will command the robot to roll over the floor, sticking to dark surfaces, based on the amount of reflected light it detects. If the robot’s body tears, it’s no big deal. Cardstock costs only about 10 to 30 cents per piece—just print another.

Ankur Mehta, who was an MIT postdoctoral fellow when he designed this machine, says his goal is to get robots into anyone’s hands for cheap. “People who are not engineers should be just as comfortable with creating and using robots as they are interacting with cellphones and smart devices,” he says.

WARNING: Lithium-polymer batteries are a fire hazard. Read the warnings on your battery before plugging it into your paper project.

Stats

  • Time: 5 hours
  • Cost: $55
  • Difficulty: Hard

Tools

  • Printer
  • X-Acto knife
  • Straight edge
  • Soldering iron

Materials

Electronics

Liz Kruesi

Electronic components for the paper robot

This article was originally published in the November 2015 issue of Popular Science, under the title “Fold a Paper Robot.”

Instructions

Erica Muxlow Hacks Cars--On A Budget

$
0
0

Erica Muxlow Races on the 24 Hours of LeMons Circuit

Photograph by Murilee Martin

Muxlow in Sesame State, her team’s hacked 1986 BMW 325es, in Buttonwillow, CA, this June. The car lost third and fourth gears midrace—and still finished.

In 2011, computer security specialist Erica Muxlow brought in her Ducati for service—but the repair shop overfilled the oil and routed the brake cable incorrectly. “I swore from then on that the only person who was going to touch my bike was me,” she says. After getting her hands dirty on her motorcycle, Muxlow decided to hack her Mini Cooper. Teaching herself, she created a “mean little high-performance street car.” Then she decided she wanted to build racecars.

Erica Muxlow

JC Images

At first, no racing teams near her Bay Area home would admit her. Several were openly skeptical that a woman had the skills to compete. She finally got her break when a work friend joined a team for the 24 Hours of LeMons, a national series of endurance races that involves cars hacked together on a budget. (Teams may only spend $500 on their cars—safety tech excluded). She hung around, proving her dedication and mechanical know-how with tasks like welding in a space so cramped, only she could fit into it.

Today, Muxlow is a full-fledged mechanic and driver for the team, which is currently ranked first on the LeMons circuit. “The other guys don’t treat me like ‘the girl,’” she says. “They treat me like a teammate.”

This article was originally published in the November 2015 issue of Popular Science, under the title “Lemon Racer.”

How To Make A Smartphone-Powered Hologram

$
0
0

Smartphone Hologram

Photograph by Bryan Edwards

Holograms aren’t just for droids and dead rappers. You can make your own with a piece of transparency paper and a four-sided hologram video. Properly folded, the transparency will combine the images on a phone or tablet screen to create “a reflection that gives you the illusion of an object hovering in space,” says Alex Cronin, a physicist at the University of Arizona.

Make the Hologram

Stats

  • Time: 10 minutes
  • Cost: $0.30-$1
  • Difficulty: Easy

Tools and Materials

  • Sheet of transparency paper
  • Pencil, pen, or marker
  • Ruler
  • Compass
  • Scissors
  • Smartphone or tablet

Instructions

Hologram Template

Levi Sharpe

Use this template to fold the transparency paper into a prism. Cut along the solid black lines and crease along the red lines.

  1. Copy the online template onto the transparency, with a radius of 4 inches or more.
  2. Cut along the solid black lines, and crease along the red lines.
  3. Tape the two opposite sides together to make a prism.
  4. Open a four-sided hologram video on your smartphone or tablet. We have one of these videos below, and you can find more by searching for "hologram video" (this is a particularly fun one).
  5. Place the small opening of the prism in the video’s center. Look through the side.

Instructions—Without a Template

No printer for the template? No problem!

  1. Use a compass and pen to draw a circle with at least a 4-inch radius on the transparency paper. Cut it out with scissors.
  2. Mark five dots around the circle, each the radius’ distance apart, and use a ruler to draw a line connecting them.
  3. Cutting along the lines, discard the rounded edges and the remaining third of the circle.
  4. Fold the trimmed transparency in fourths to make four separate equilateral triangles. Cut off their tips about an inch from the bottom and tape the two opposite sides together to make a prism.
  5. Open a four-sided hologram video on your smartphone or tablet. We have one of these videos below, and you can find more by searching for "hologram video" (this is a particularly fun one).
  6. Place the small opening of the prism in the video’s center. Look through the side.

More Optics Hacks

A smartphone can perform other optical tricks. Harvest a focus lens from a laser pointer, and attach it to the phone’s camera with some wire. The lens will magnify images to make a DIY microscope (full instructions here). Or stick a few pieces of clear tape over the flash, and color them with blue and purple Sharpie markers. This filter blocks out most visible light and leaves only the ultraviolet spectrum, turning the phone's flashlight function into a blacklight (full instructions here).

This article was originally published in the November 2015 issue of Popular Science, under the title "Smartphone Hologram."


Seven Decades Later, Cars Still Need To Get Lighter

$
0
0
Cover of Popular Science magazine from May 1951 with three cars zooming past

May 1951

Popular Science

Yes, in the 1950s, Popular Science actually used the Indianapolis 500 racetrack for testing consumer cars.

In May 1951, racecar driver Wilbur Shaw tested a batch of cars that—in contrast to the veritable barges trendy at the time—were billed as “little.” They were cheap to purchase and drive. “You get what you pay for, and no more,” was Shaw’s assessment of the Henry J (in blue), which cost $1,360—about $12,500 in today’s dollars. It lacked such amenities as a trunk door (penny-pinching owners would need to fold down the rear seats to retrieve their luggage). The pioneering compact car didn’t sell, and Kaiser-Frazier manufactured it for only a few years. Though smaller cars did start finding favor in the 1970s, few of today’s models are so light: At 2,300 pounds, the Henry J weighed about as much as a Fiat 500. But with U.S. fuel-efficiency requirements rising to 54.5 miles per gallon in 2025 (from 34.1 today), cars need to get lighter again, and quickly. Carbon fiber and 3D printing might help automakers get there.

Popular Science’s Enduring Love For Cars

The postwar years saw a jump in the magazine’s auto coverage, a trend that lasted decades. From 1950 to 1980—when high-tech items such as computers start to appear—nearly every issue ran articles on cars, and many covers featured images of autos and their attendant tech.

Line chart showing use of the word "car" and "auto" in Popular Science from 1917 to 2009

Katie Peek

Wilbur Shaw, The Race Champion Who Tested Our Vehicles

Wilbur Shaw

Popular Science, August 1950; illustration by Reynold Brown

In August 1950, Popular Science debuted a new column: consumer cars, reviewed by the auto-racing champion Wilbur Shaw. Shaw won the Indianapolis 500 three times and became president of the organization after he saved the race from cancellation in 1946. He used the speedway to test cars for his reviews. The column ended abruptly when a plane crash killed Shaw in October 1954. He had been flying home from Detroit, where he was driving a new Chrysler luxury car for Popular Science.

This article was originally published in the November 2015 issue of Popular Science, under the title “Efficient Autos Hit the Road.”

Does "Bracing For Impact" Really Protect You In A Crash?

$
0
0

Hold on!

Jason Schneider

On January 8, 1989, a Boeing jetliner crashed during an emergency landing near East Midlands airport in England, killing one-third of the passengers on board. As doctors tended to survivors, they found that people who had adopted a “brace position” prior to the crash—heads bent forward, feet planted on the floor—were less likely to have sustained severe head trauma or concussions, no matter where they sat on the plane.

The Federal Aviation Administration has been using test dummies to study brace positions since 1967. While the recommended postures have changed a bit over the years, the underlying principle remains unchanged: It’s best to lean forward in advance of a plane crash so your head is close to the seat in front of you. To press yourself toward the back of that seat, the theory goes, reduces the risk of deadly “secondary impact,” wherein your head whips forward and slams into a hard surface.

Passengers in car accidents, who might have less time to act before a crash, reflexively brace for impact too. One study found that at least half the victims in head-on collisions press their heads and torsos back against their seats, locking their arms against the steering wheel or dashboard. While this position might increase the risk of breaking an arm or leg, it helps protect the head and chest from severe injuries.

Of course, the safest crash position depends on the nature of the accident and the design of the vehicle. Dipan Bose, a transport specialist with the World Bank, has studied emergency bracing positions using computer simulations. “This is all very directional,” he says. “You have to know exactly which way the body will move.” Easier said than done when it comes to car accidents, which are, by nature, unpredictable.

This article was originally published in the November 2015 issue of Popular Science

Build A 300-MPH Ping-Pong Cannon

$
0
0

William Gurstelle And His Pingpong Cannon

Photograph by Ackerman + Gruber

The fastest recorded table-tennis smash, achieved by New Zealand’s Lark Brandt at the 2003 World Fastest Smash Competition, was a mere 69.9 miles per hour. That's less than a quarter of the speed of a ball shot from this pingpong cannon.

A world-class table-tennis player can smash the ball at almost 70 miles per hour. From my experience, it is darn difficult to return the ball at such speeds. Imagine a shot delivered more than four times faster—could even the best player hit it? To find out, I designed a ping-pong cannon that shoots balls at nearly half the speed of sound.

The cannon’s power comes from Boyle’s Law, which (simplified) says that pressure is inversely related to volume. For example, if you put the air in a small reservoir under a lot of pressure and then release it into a larger one—such as the barrel of a gun—the pressure will drop. This causes the air’s volume to expand instantly, shooting out any objects, like bullets, sharing that space.

Boyle’s Law was also used to great advantage in one of the most historically important air guns of all time: the Corps of Discovery Air Rifle. It was wielded by the Austrian army at the turn of the 18th century but became best known as the weapon carried by Meriwether Lewis during the Lewis and Clark expedition of 1803-06. His rifle can still be seen today in the Virginia Military Institute Museum.

I built my own take on Lewis’ weapon out of PVC piping. A small piece of pipe serves as the air reservoir. A water-sprinkler valve, which costs about $15 at the hardware store, controls the opening. I connected the valve’s top cover to my air compressor’s blowgun attachment. Then I pressurized the reservoir by adding air with a bicycle pump. When I pull the blowgun lever, it opens a port in the sprinkler valve, allowing high-pressure reservoir air to move into the longer PVC pipe that serves as the barrel. As the gas expands, it ejects a pre-loaded ping-pong ball.

Measuring the speed with a ballistic chronograph, I recorded velocities greater than 300 miles per hour. So could a great table-tennis player actually return a serve at this speed? I recruited a volunteer and pressurized the cannon—check out the video at the end to see what happened.

WARNING: Don’t stand in front of a ping-pong cannon—for obvious reasons.

Build Your Own Ping-Pong Cannon

This device shoots a ping-pong ball at high speed, and it’s not hard to build. I don’t recommend you actually try to incorporate it in your table-tennis practice unless you dial way back on the air pressure. With more than, say, 10 psi in the pressure reservoir, you don’t want to be anywhere near the muzzle end of this shooter when it fires.

Use your head, wear eye protection, and proceed, as always, at your own risk. PVC manufacturers do not recommend compressed applications for their product. While I have never had a problem with the device at the relatively low pressures described here, it can be dangerous. So use PVC at your own risk—or you can substitute steel pipe for the plastic.

Materials

(5 feet) 1½-inch-diameter PVC pipe
(1) 1½-inch socket-to-socket coupling
(2) 1½-inch spigot X 1-inch female pipe threaded reducing bushing
(2) 1-inch NPT close iron pipe nipples
(1) 1-inch in-line sprinkler valve
(1) Compressed-air palm-type blowgun (make sure the one you buy has a ¼-inch NPT air connection)
(18-inch) 3-inch diameter PVC pipe
(1) 3-inch socket-style PVC end cap
(1) ¼-inch NPT air-tank valve
(1) ¼ inch NPT 0 to 60 psi pressure gauge
(1) ¼-inch diameter NPT brass hex or regular nipple, 1 inch long, 1/Block
Strapping tape
Vinyl or aluminum tape
ping-pong balls

Part One – Modify the Sprinkler Valve

Water-sprinkler valves are used in lawn-irrigation systems.

  1. Disassemble the sprinkler valve. On some models the top unscrews, and on others you’ll need to remove screws or bolts holding the top to the body.
  2. Drill a 7/16-inch hole in the center of the top. Insert a ¼-inch NPT tap into the tap handle, and cut screw threads into the hole you just made.

Modified Sprinkler Valve

William Gurstelle

  1. Apply pipe thread sealant to one end of the ¼-inch-diameter, 1-inch-long NPT brass nipple, and screw it into the tapped hole you just made.
  2. Apply pipe-thread sealant to the other end of the ¼-inch-diameter NPT brass hex nipple, and screw on the ¼-NPT opening on the blowgun.
  3. Block the solenoid air hole (see the photograph) by inserting a sheet-metal screw and then covering it with epoxy or hot glue. Reattach the top to the valve body.

Part Two – The Pressure Reservoir

Pingpong Cannon Assembly Diagram

William Gurstelle

  1. Take a look at the Near Supersonic Shooter Assembly Diagram. Drill a 7/16-inch hole in the center of the 3-inch PVC endcap for the Schrader valve and in the 3-inch-diameter pipe for the pressure gauge. Use the ¼-NPT pipe tap to cut ¼-NPT threads in the hole. Apply sealant and then insert the ¼-inch tank valve in the endcap, and the pressure gauge in the pipe.
  2. Assemble the reservoir as shown in the diagram using PVC cement. Follow all cement and primer label directions carefully.
  3. Neatly wrap the pressure reservoir with strapping tape.

Part Three – Assemble It

  1. Screw the modified valve assembly into the 1-inch female-pipe-thread opening on the pressure reservoir.
  2. Screw the valve assembly into the 1-inch female-pipe-thread opening on the barrel assembly, using sealant to prevent leaks.
  3. Use the compressor to pressurize the air in the reservoir to 15 psi. Watch the pressure valve to see if any air leaks. If any does, you’ll need to find the leaks by spraying soapy water on all your connections and look for bubbles. Then, press the trigger on the blowgun and test the operation of the valve. Release the air when done.

Operation

WARNING: Before using the cannon, review the following commonsense safety rules:

  • Use at your own risk.
  • Wear safety glasses.
  • This cannon shoots with enough force to cause great harm.
  • Do not look down the barrel.
  • Always know where the barrel is pointing. Aim only at targets you intend to hit.
  1. Insert the ping-pong ball, and push it as far down the barrel as it will go.
  2. With the air compressor, pressurize the air reservoir. Remember, the higher the pressure, the more dangerous the device becomes.
  3. Once you are sure your gun is aimed at a suitable target, press the trigger on the blowgun. The gun will fire with a loud report and a whopping amount of power!

This article was originally published in the November 2015 issue of Popular Science, under the title “I Built a 300 MPH Pingpong Cannon.”

How Accurate Are Calorie Counts On Food Labels?

$
0
0

Jason Schneider

America’s century-old system for counting calories comes from chemist Wilbur Atwater. In 1887, he began to research the energy we get from eating by measuring the stored energy in foods and subtracting the amount left in people’s bodily excretions.

Atwater’s research has since been boiled down to the 4-9-4 rule: Each gram of protein, fat, and carbohydrate provides, respectively, 4, 9, and 4 calories of energy. The United States Department of Agriculture (USDA) has used these figures for decades, tweaking them only to account for different qualities—such as the digestibility—of specific foodstuffs.

But in the past few years, nutritionists have clamored for a reappraisal. For one thing, they say the present system ignores the difference between raw and cooked food. Harvard University researchers assert, based on mouse studies, that processed food is easier for the body to absorb, so it provides more calories. That goes for baked or blended food. Even a handful of chopped peanuts gives you more energy than whole ones.

In 2011, USDA researchers, with a grant from the nut industry, reported that the caloric value of pistachios had been overstated by 5 percent. In 2012, they found almonds were overstated by 32 percent, or 40 calories per serving. So you might not want to take nutrition labels at face value.

This article was originally published in the November 2015 issue of Popular Science

Sculptures With A Life Of Their Own

$
0
0

Theo Jansen And His Strandbeest

Photograph by Loek Van Der Klis / Flickr

Theo Jansen and one of his strandbeests, Animaris Umerus, walk along a beach in the Netherlands.

Twenty-five years ago, artist Theo Jansen built a new life-form. Made of PVC pipes and zip ties, his strandbeest (Dutch for “beach beast”) walked along a beach under wind propulsion. Since then, Jansen has created many more beests and inspired a small army of imitators. "The perfect strandbeest is a specimen that lives on its own," he says, "so I don’t have to think about it anymore." Some of his strandbeests, and other makers’ so-called hackbeests (see the image gallery below), will begin their first-ever tour of U.S. museums this fall. They will be on view at their first stop, Salem’s Peabody Essex Museum, through January.

This article was originally published in the November 2015 issue of Popular Science, under the title “Sculptures with a Life of Their Own.”

Viewing all 20161 articles
Browse latest View live




Latest Images